Print | Open Full Page | Save to PDF | Add To Catalog

Power Shield Box Insert MSDS

Material Identification

Product Name: SpecSeal® Power Shield™ Box Insert
Chemical Family: Does Not Apply
Company Identification
Manufacture/Distributor
Specified Technologies, Inc.
200 Evans Way
Somerville, NJ 08876
Phone Numbers
Product Information: 1-908-526-8000
Emergency: 1-800-255-3924
Composition/Information on Ingredients
Non-hazardous, flexible rubber strip
Hazards Identification
***********EMERGENCY OVERVIEW***********
* Possible Skin and Eye Irritant. Red Solid. *
***********************************************************
Potential Health Effects:
EYE: Contact my cause irritation
SKIN: Contact may cause irritation
INGESTION: Not likely.
INHALATION: No hazard
CHRONIC (CANCER) INFORMATION: None known.
LONG TERM TOXIC EFFECTS: None known.
First Aid Measures
INHALATION: None applicable
SKIN CONTACT: None applicable
EYE CONTACT: Irrigate eyes with running water for at least 15 minutes.  Get medical attention if irritation develops
INGESTION: None applicable
Fire Fighting Measures
FLASH POINT: Not established
EXTINGUISHING MEDIA: Dry Chemical; Carbon Dioxide; Foam; Water spray for large fires
SPECIAL FIRE FIGHTING PROCEDURES: As for surrounding fire
Accidental Release Measures
Safeguards (Personnel)
NOTE: Review FIRE FIGHTING MEASURES and HANDLING (PERSONNEL) sections before proceeding with clean-up.  Use appropriate PERSONAL PROTECTIVE EQUIPMENT during clean-up.
Handling and Storage
Store under ambient conditions.  No special handling required.
Exposure Controls/Personal Protection
EYE PROTECTION REQUIREMENTS: Safety glasses/goggles
SKIN PROTECTION REQUIREMENTS: None
RESPIRATOR REQUIREMENTS: None
VENTILATION REQUIREMENTS: If needed, use local exhaust ventilation to keep airborne concentrations below the TLV
Exposure Guidelines: None
Exposure limits: None
Physical and Chemical Properties
PHYSICAL FORM: Flexible rubber strip
SPECIFIC GRAVITY: 1.38
PERCENT VOLATILES: 0
SOLUBILITY IN WATER:Insoluble
Stability and Reactivity
STABILITY: This is a stable material
CONDITIONS TO AVOID:None
HAZARDOUS POLYMERIZATION: Will not occur
INCOMPATIBILITIES: None special
Toxicological Information
Mixture not tested by based on components:
Particles may cause physical irritation to eyes.
Contains no carcinogens as specified by IARC, ACGIH and NTP or OSHA
Ecological Information
Non data.  Not anticipated to be environmental hazard.
Disposal Considerations
Waste Disposal:  Treatment, storage, transportation, and disposal must be in accordance with applicable Federal, State/Provincial, and Local regulations
Transportation Information
DOT - not regulated
Regulatory Information
U.S. Federal Regulations
TSCA Inventory Status: Article
Section 313 Supplier Notifications.
This product contains no toxic chemicals subject to the reporting requirements of Section 313 of the Emergency Planning and Community Right-To-Know Act of 1986 and of 40 CFR 372.
Other Information
NPCA-HMIS Rating
  • Health: 0
  • Flammability: 1
  • Reactivity: 0
Personal Protection rating to be supplied by user depending on use conditions.
STATE RIGHT-TO-KNOW LAWS
No substances on the state hazardous substances list, for the states indicated below, are used in the manufacture of products on this Material Safety Data Sheet, with the exceptions indicated. While we do not specifically analyze these products, or the raw materials used in their manufacture, for substances on various state hazardous substances lists, to the best of our knowledge the products on this Material Safety Data Sheet contain no such substances except for those specifically listed below:
SUBSTANCES ON THE NEW JERSEY WORKPLACE HAZARDOUS SUBSTANCE LIST PRESENT AT A CONCENTRATION OF 1% OR MORE (0.1% FOR SUBSTANCES IDENTIFIED AS CARCINOGENS, MUTAGENS OR TERATOGENS): NJTSRN-SSP WARNING: SUBSTANCES KNOWN TO THE STATE OF CALIFORNIA TO CAUSE CANCER: Possible traces of formaldehyde and acrylonitrile.
WARNING: SUBSTANCES KNOWN TO THE STATE OF CALIFORNIA TO CAUSE BIRTH DEFECTS OR OTHER REPRODUCTIVE
HARM: None known.

 


This information relates to the specific material designated and may not be valid for such material used in combination with any other materials or in any process. Such information is to the best of our knowledge and belief accurate and reliable as of the data compiled. However, no representation, warranty, or guarantee is made as to its accuracy, reliability or completeness. It is the user's responsibility to satisfy himself as to the suitability and completeness of such information for his own particular use. We do not accept liability for any loss or damage that may occur form the use of this information.
Responsibility for MSDS :
Specified Technologies, Inc.
200 Evans Way
Somerville, NJ 08876

 

Print | Open Full Page | Save to PDF | Add To Catalog